ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.
|Published (Last):||20 March 2011|
|PDF File Size:||1.91 Mb|
|ePub File Size:||4.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
Greater separation shall be cause for rejection.
Such requirements may include, but are not limited to the following: When none has been speci? The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. A list a2265 standardized supplementary requirements for use at the option of the purchaser are included in Speci?
Ultrasonic Examination in accordance with Speci?
The sides of the bend test specimen used for bond strength determination may have the corners rounded to a radius not over 1? This standard has been approved for use by agencies of the Department of Defense. The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance. A — 09 Standard Speci? For purposes of de?
Gage Length cladding and the base steel shall be machined so as to maintain the same ratio of clad metal to base steel as is maintained in the plate, except that the thickness of the clad material need not be reduced below 1? Permissible Variations Metric Equivalents in. Originally approved in If spectrometric procedures are used, the sample shall be exposed on the center line of the cladding when there is sufficient cladding thickness available so that there is no contamination from the adjacent base metal.
ASTM A265 Clad Plate
Repair of Cladding by Welding The material shall be cleaned and sufficient millings taken to represent the full cross-section of the remainder. General Requirements for Delivery It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
A number in parentheses indicates the year of last reapproval. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
All other tensile test requirements of the speci?
ASTM A GR 1 titanium alloy strip sheet plate
The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. In reducing the thickness of the specimen, both the alloy 3 Metric Equivalents in. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
The tensile properties thus determined shall meet the base steel requirements. This abstract is a brief summary of the referenced standard. Current edition approved May 1, If the requirements of this speci? Chemical analysis may be accomplished by wet chemical or instrumental procedures. If wet chemical procedures are used, millings may be taken only when the composite plate thickness is sufficient to permit obtaining millings without danger of contamination from the adjacent layer.
Workmanship Finish, and Appearance This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Link to Active This link will always route to the current Active version of the standard.
This specification covers the standard for plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of nickel or nickel-base alloy.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. The shear test, when speci?
ASTM A265 GR 1 titanium alloy strip sheet plate
Testing for shear strength for clad plates with minimum cladding thickness of 0. Reports shall include the results of ultrasonic inspection when Supplementary Requirement S12 is speci?
The surface condition of the repaired area shall be restored to a condition similar to the rest of the cladding. Last previous edition approved in as A — NOTE 3—The dimension t is the thickness of the test specimen as provided for in the applicable material speci? Approved May 1, Several of those considered suitable for use with this speci?