Buy ASTM D Standard Practice for Manual Sampling of Petroleum and Petroleum Products from SAI Global. ASTM D Standard Practice for Manual Sampling of Petroleum and Petroleum Products. standard by ASTM International, 12/01/ View all product. Find the most up-to-date version of ASTM D at Engineering
|Published (Last):||14 September 2009|
|PDF File Size:||17.3 Mb|
|ePub File Size:||13.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is good 6. Proceed in accordance with Sections 7 and 6, five of the sampling points shown in Fig. In most from moisture and dust by placing paper, plastic, or metal foil cases, the number specified in Table 3 will be satisfactory.
Petroleum coke may qstm on a hard, clean surface, free from cracks, and protected from sampled while being loaded into railroad cars from piles or rain, snow, wind, and sun. Such instructions supplement the general procedures of may be taken by mutual agreement by the following methods: The valves snap shut when the thief is withdrawn. A number in parentheses indicates the year of last reapproval. When atm tube reaches the bottom, remove the Aastm 2 – The procedure for sampling liquefied petroleum gases is described in Practice D ; the procedure for sampling fluid power hydraulic fluids is covered in ANSI B Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM D – 12() Standard Practice for Manual Sampling of Petroleum and Petroleum Products
Special Instructions for Specific Tests Use only clean, dry cans, or glass bottles as sample containers. Emulsified asphalts storage tanks, tank cars, lines, packages Allow adequate room for expansion, taking into consideration the temperature of the liquid at the time of filling, It is preferable to take sample will finally be reduced to a representative, suitable size samples during the unloading of cars or during transit; obtain for laboratory purposes.
The sampling cage any desired level, shall be made of a metal or plastic suitably constructed to hold f A thief cord marked so that the sample can be taken at the appropriate container. Perform the quartering operation ods of shipping or handling are used. A The respective sets of taps should be located on opposite sides of the tank.
The procedure for sampling bituminous materials is described in Practice D For greases Container Lot or Shipment Minimum Sample having a penetration of less thancut samples from each Tubes or packages, less All enough units for a 4. Use waterproof and oil proof ink or Do not agitate the bottle while drawing the sample.
See Practice D for additional information concerning the 9. When the respective tests awtm performed on individual that have stratified to ensure that a representative sample is samples, which is the recommended procedure, the test results available for transfer to an intermediate container or the are averaged generally. Prior to further use, reusable containers 7.
It is important stream. Insert the tube FIG. This method may also be used asfm tanks up to and including a capacity of m3 bbls. This test method has been approved by the sponsoring committees and accepted by the Cooperating Societies in accordance with established procedures. Solids or semi-liquids that can be sample bottle from the sampling cage, as applicable.
Bottom sample location must be 60 50 20 5 5 specified. Collect the sample s directly in a clean, dry bottle s or other appropriate container d44057.
If detection of water, rust, or other seller. USC units are reflected in parentheses.
ASTM D – 06 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
Procedures are also included for the sampling of free water d457 other heavy components associated with petroleum and petroleum products. Upper tap 45 cm 18 in. Avoid handling any part of the tube that will be immersed in the oil during the sampling operation. As examples, a spot sample provides a sample from only one particular point in the tank, vessel compartment, or pipeline.
Two rings soldered to tighten the bung in the drum or barrel.
See Practice D for more detailed instructions. Skip to main content. In order to reduce the potential for documented and care taken to preserve the integrity of the static charge, nylon or polyester rope, cords, or clothing should samples.
Multi-Level Self-Sealing Sampler
Prepare a composite sample of at least 1 L 1 qt by a temperature of 0 to 4. Manual Pipeline Sampling Select at random the individual pack- sensitive to light, such as gasoline, be kept in the dark, if the ages to be sampled. To be able to select the right container for a a Discussion—Stand pipes may also be found on ships and given application one must have knowledge of the material to barges.
The size of the core thief should be selected depending upon the volume of the sample required. Practice D con- tions should be taken to ensure its removal. Obtain at least 4 L 1 gal or 4.