View and Download HP X – JetDirect Print Server hardware installation manual online. HP JetDirect External Print Servers X, X X, EX Plus. This step by step instruction describes how to setup a HP Jetdirect x print server so that the 8 bits output can be controlled by a user made program or from a. One is configuring a new, unconfigured HP Jetdirect and the other is reconfiguring an already configured HP Jetdirect. Below are the instructions for each.
|Published (Last):||6 January 2017|
|PDF File Size:||17.35 Mb|
|ePub File Size:||3.53 Mb|
|Price:||Free* [*Free Regsitration Required]|
For Windows systems, note the following: DO NOT use this program when you’re in a hurry – you might screw up your print server!!!! If you have difficulty viewing documents, upgrade to the latest released version of Acrobat Reader. In addition, check the cabling andconnectors. The protocol is not routable, that is,the workstation from which the configuration is made must belocated on the same network segment as the HP Jetdirect printserver.
HP Jetdirect x Print Server series User Guides | HP® Customer Support
To select another name, repeat steps 4 and 5. See Appendix A for parallel cables available fromHP. Make sure yourHP Jetdirect print server is correctly attached to yournetwork.
Page 47 To configure a Jetdirect print server, use the followingcommands.
Page 18 Print a X Configuration PageA 170d page shows print server status and configurationparameter settings. Take a DB25 male connector and connect pins 1, 10, 13 and 15 together. Page of 80 Go. The HP X configuration page is divided into the following sections: The tagsare identified in the following table. For example, a small workgroupmight use peer-to-peer printing even though it is connected toan enterprise-wide client-server network.
Start your web browser and go to the Jetdirect’s web interface by typing its IP address in the location bar. Microsoft Internet Jettdirect 5. Page 17 The X does not have a power switch.
Refer to your network operating systemmanuals to verify jetdirectt your operating system supportsDHCP. To disable, set to 0. Page 56 Moving to Another NetworkWhen moving an Jetdirevt Jetdirect print server that is configuredwith an IP address to a new network, make sure that the IPaddress does not conflict with addresses on the new network. How to control your HP Jetdirect x This step by step instruction describes how to setup a HP Jetdirect x print server so that the 8 bits output can be controlled by a user made program or from a PHP script.
What’s missing? Tell us about it.
This name identifies an entry point toa list of parameters for a specific peripheral. Vigencia de la garantia: If Required, Configure the X withYour Network SettingsIf your network requires that you configure network settings on theprint server before you add the printer to your network systems, youcan do so now using available configuration tools.
Test button sends print server configuration page. When you hold down the Test button for three seconds, the LEDs begin to cycle through four configurations, as outlined in the following table. Specifications and Regulatory StatementsSpecifications.
Connect the X to the network with a 10Base-T network cable. After you install the ketdirect server, the next step will be to configure it. Got it, continue to print. To accomplish this you need a tool that can send and receive SNMP commands.
Page 83 Table 6. The Jetdirect should be reset now and is configured by default jedtirect obtain an IP address automatically. Plug the X power module into a wall outlet.
HP Jetdirect 170x Print Server series User Guides
On Solid Encountering a fault during self-test or operation. It is retained after a power cycle. Page 19 If Required, Configure the X withYour Network SettingsIf your network requires that you configure network settings on theprint server before you add the printer to your network systems, youcan do manua, now using available configuration tools. Page 40 NoteIf subnetting is used, the subnet mask defineswhich portion of an IP address specifies thesubnet and which portion specifies the clientdevice.