Kenty PDF

LS datasheet, LS circuit, LS data sheet: LSI – BIT QUADRATURE COUNTER,alldatasheet, datasheet, Datasheet search site for Electronic. LSI LS 30 available from 2 distributors. Explore LSI on Octopart: the fastest source for datasheets, pricing, specs and availability. The LSI Computer Systems LS is a CMOS, bit counter that can be programmed to operate in several View the Manufacturer’s Datasheet. Features.

Author: Digal Yoktilar
Country: Cyprus
Language: English (Spanish)
Genre: Software
Published (Last): 4 December 2010
Pages: 438
PDF File Size: 9.25 Mb
ePub File Size: 8.95 Mb
ISBN: 970-7-57075-885-5
Downloads: 15429
Price: Free* [*Free Regsitration Required]
Uploader: Vukus

The following is a list of registers and the general use of each, even though they are le7166 handled by the code written in a later section.

A chip with similar capability is the LSRwhich uses the SPI bus to communicate instead of in parallel, is discussed on separate wiki page.

LS | LSI CORPORATION (LSI LOGIC) | DATASHEET | PHOTO

Because of this, if running the motor backwards continuously counting downthe value of CNTR will always be between 0 and PR at the current position. The chip has several other features that can be read about in the datasheet. The LS, as mentioned above, connects to the PIC via an 8-bit data bus, 4 control bits, 2 optional control bits, and 2 optional flags. Note that at the end of the init function, the counter limit value is loaded into the PR register.

As mentioned above, multiple LS can be used which are connected to the same data and control lines, except for chip select, which needs to be separate for each datasehet.

  KBU8G DATASHEET PDF

LS7166 Datasheet PDF

This number should ls166 changed based on the full rotation count of the encoder in use. A motor’s encoder can be connected directly to the LS, which will decode and count pulses as the encoder channels change. For more info on these features, see the datasheet. In the code below and example schematic, pins B0-B7 are used for the data bus.

Note that to use thethe only steps are to setup the pins, call the init function, then call the read function to get a value. This c file contains various functions used to interface with the LS Because of this, the pic software must be written so that the read value of CNTR is modded by the maximum count number to find the position.

For instance, if the maximum count isand CNTR isthen the actual position is out of Eventually the CNTR will overflow if datasheeg reduced.

In any motor-related application, binary counting is necessary. The LS is a 24 bit quadrature counter. Most other functions will usually dattasheet be needed unless special features are needed.

LS709T, LS7100, LS7166

This c file simply loops continuously and reads values from the LS The LS communicates with a microcontroller via a bi-directional 8-bit data bus and several control bits. Since this was put in the separate function, other code won’t have to be changed, other than TRIS setups. All three can be download from this zip file. These pins can be changed, but the data bus read and write functions will need to be changed to interface with bit lines instead of bytes.

Note that most pins are active low, and thus must be kept at high at all times unless in use. This is useful for motor applications, since the fixed value can be set to the number of pulses in a full rotation, and then whenever the count value is read, the exact position of the motor can be known no matter the amount of time that has passed since the last read.

  2SC2235 DATASHEET PDF

The init function can be modified to utilize other special features of the chip not used here.

The value of the PR register is loaded whenever the counter borrows downticks from 0. Personal tools Log in. Retrieved from ” http: The A and B inputs normally serve as quadrature inputs, like those which come from a quadrature encoder like those on most motors.

LS Datasheet(PDF) – LSI Computer Systems

The chip can also operate in divide-by-n mode, which loads the count register with a fixed value on rollover. Using a parallel data bus, a microcontroller can datsheet read the current count value from the chip, allowing a project to interface with motor encoders without using any additional timers.

Views Page Discussion View source History. The code in this document only covers divide-by-n binary quadrature mode, and for more advanced features the daatasheet code will need to be modified. Alternatively, at each read the PIC could send back the actual count value.