Kenty PDF

This standard is issued under the fixed designation A ; the 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. NOTE 1—A complete metric companion to Specification A has been developed—Specification AM; therefore no metric equivalents are presented in this. Standard Specification for Tin Mill Products, General Requirements. Status: Withdrawn · Replaced by: ASTM A Buy this standard. Price: SEK. PDF.

Author: Tukinos Zulkirn
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Photos
Published (Last): 27 February 2008
Pages: 423
PDF File Size: 20.32 Mb
ePub File Size: 8.85 Mb
ISBN: 824-6-27249-233-4
Downloads: 81829
Price: Free* [*Free Regsitration Required]
Uploader: Tygogul

The mechanical properties of continuously annealed plate and batch annealed plate of the same Rockwell astj temper designation are not identical. The steel shall be made by the open-hearth, electric-furnace, or basic-oxygen process.

Historical Version s – view previous versions of standard. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. A complete inch-pound companion to Specification AM has been developed—A; therefore, no inch-pound equivalents are presented. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  HP-41CX OWNERS MANUAL VOL 2 PDF

Standard – Standard Specification for Tin Mill Products, General Requirements ASTM A –

This abstract is a brief summary of the referenced standard. The steel shall be made by the open-hearth, electric-furnace, or basic-oxygen process.

Link to Active This link will always route to the asym Active version of the standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Link to Active This link will always route to the current Active version of the standard. Rockwell 30T hardness test shall be done to the plates.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to asfm its use and application. A complete metric companion to Specification A has been asm AM ; therefore no metric equivalents are presented in this specification.

This specification covers a group of common requirements which shall apply to tin mill products. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

It is important to keep in mind, that the Rockwell 30T test does not measure all various factors which contribute to the fabrication characteristics of the plate. The steel shall conform to specified chemical composition requirements.

  EZ 12 PARABOLIC REFLECTOR TEMPLATE PDF

Standard Specification for Tin Mill Products, General Requirements

The mechanical properties of continuously annealed plate and batch annealed plate of the same Rockwell 30T temper designation are not identical.

This specification covers a group of common requirements which shall apply to tin mill products. This standard does not purport to address all of the safety concerns, if any, associated with its use. This test forms the basis for a system of temper designation.

ASTM AM – 16 Standard Specification for Tin Mill Products, General Requirements [Metric]

It is important to keep in mind, that the Rockwell 30T test does not measure all various factors which contribute to the fabrication characteristics of the plate. The steel shall conform to specified chemical composition requirements. Rockwell 30T hardness test shall be done to the plates. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

This standard does not purport to address all of the safety concerns, if any, associated with its use. This test forms the basis for a system of temper designation. This abstract is a brief summary of the referenced standard. Historical Version s – view previous versions of standard.