Kenty PDF

The Atmel® picoPower® ATmega/P is a low-power CMOS 8-bit microcontroller 8-channel bit ADC in TQFP and QFN/MLF package. •. Temperature. Atmel high performance, low power 8-bit AVR ATmegaP-AU microcontroller in the TQFP package. Okay, so I’m about to blow up. I’ve tried to use perhaps 10 Atmega TQFP without any success.

Author: Kajihn Shakinos
Country: Samoa
Language: English (Spanish)
Genre: Education
Published (Last): 15 July 2016
Pages: 242
PDF File Size: 5.17 Mb
ePub File Size: 20.44 Mb
ISBN: 450-4-46453-777-7
Downloads: 43388
Price: Free* [*Free Regsitration Required]
Uploader: Akinokree

Any help would be appreciated. Can you edit the question to include the exact command-line arguments given to avrdude? I’m voting to close this question as off-topic because it has been abandoned for half atmega38 year in unanswerable state.

Atmega 2 9 Home Questions Tags Users Unanswered. Using SCK period of 10 usec avrdude: However, when attempting to upload the bootloader to the chip, I am presented with the following error:.

Assuming your connection is incorrect, first you need to add a pull-up resistor to the reset pin; 1kk should be alright. Ground yourself and use an ESD mat.

ATmegaP Microcontroller – TQFP | ATmegaTQFP | Atmel

ISP requires a working clock source. TomCarpenter, the programmer does provide power.

It’s worth checking its in the correct position, though. When programming through SPI, the chip accepts the program even if the fuses are set to accept clock signal from external clock.

  DIETA DE LA ENZIMA PRODIGIOSA PDF

If all that is correct, there are a couple other things that could cause that error:.

I’ve simply connected the AVR programmer to the chip in the adapter socket as follows AVR connector on left, chip attmega328 right. Clearly I’m doing something incorrectly, and I wouldn’t doubt if it was because it’s not as simple as hooking the AVR programmer directly up to the chip to program it.

Reset is driven by the programmer, and besides has an internal pullup.

Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size Pages MinW MaxW ReadBack eeprom 65 20 4 0 no 4 0 0xff 0xff flash 65 6 0 yes 0xff 0xff lfuse 0 0 0 0 no 1 0 0 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 0x00 0x00 efuse 0 0 0 0 no 1 0 0 0x00 0x00 lock 0 0 0 0 no 1 0 0 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type: ATmegaP Chip Erase delay: That is pretty much all you need.

If all that is correct, there are a couple other things that could cause that error: If the reset pin has been disabled, you’ll need a special high voltage 12V programmer to recover it. Only HV programming does not.

Check that the ISP header connects to the pins that it ought to, and check that you have the chip oriented correctly in the socket Atmeta328 USBtiny has a switch to power the target, so make sure that’s in the correct position. This question does not appear to be about electronics design within the scope defined in the help center.

  ARVORE DO CONHECIMENTO MATURANA E VARELA PDF

Have you applied power to the circuit? Crystal requirement comes when booting through the bootloader i. The reset pin lacks the normal ESD protection, and so is fairly easy to fry.

It looks like the log text says ‘programmer operation not supported’, could be a symptom of bad cmd line args. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Hqfp of Service.

Error while burning bootloader.

ATMega328 – TQFP

If you have ever managed tqfpp program the fuses, the reset pin may have been disabled, or the device may be expecting an external crystal. SCK serial program mode: Well first of all, check the wiring. If this question can be reworded to fit the rules in the help centerplease edit the question.

The AVR programmer will not supply power.