Kenty PDF

, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel:. MFG:. ATTANSIC. Picture. D/C:. 09+. QTY:. Packaging:. SOP8L. Package:. Note:. 原装正品. Support. No“ATTP1”Picture.

Author: Aralabar Tojasar
Country: Indonesia
Language: English (Spanish)
Genre: Automotive
Published (Last): 21 April 2013
Pages: 400
PDF File Size: 13.68 Mb
ePub File Size: 1.28 Mb
ISBN: 792-9-56847-786-3
Downloads: 63701
Price: Free* [*Free Regsitration Required]
Uploader: Brakasa

Make sure you leave just a dollop of solder on the end of the jumper wire when you tin it or you’ll never get it to solder properly but don’t leave too much, or you’ll bridge the pins.

ATTP1_1.3.pdf

It is the 4th pin from the top right corner of the chip going down the right side of the chip, when viewed as described above. I just have you solder directly to the pin because it is simpler to explain.

Anything else is nearly impossible. That’s all there is to it. It didn’t change my temp readings at all, but it is theoretically possible for there to be a slight change in the reading. The jumper wire will need to be about 3. You don’t need to move the jumper though. Solder to pin 61 first, then pin Atto1 to test OTP? This is the top right pin on the Attansic chip, when viewed with the mobo oriented as described above.

  DIVORCE DOC1 PDF

Attansic ATTP1 datasheet & applicatoin notes – Datasheet Archive

Webb City, Mo Posts: This is the analog voltage input. However, because of the way the mod is done, the odds of messing it up in such a way that you dissable the OTP function are pretty low.

You should thread the jumper first, then solder to the Attansic chip, then finally solder to the Winbond chip. I will have no sympathy. As for the attansic, does it have a thermal diode?

Our members offer you their FAQs! This is the 5vsb input.

ATTP1 – – IC Chips – Kynix Semiconductor

However, be attp11 that soldering pin 97 and pin back down is rather tricky because of the fine spacing of the pins. The wire will need to be about 8 cm 3″ long. I didn’t think it did.

While this mod works pretty well, it has one glaring drawback, which I mentioned in the previous post: Lift this pin just as you did pin I’ve been looking for developer’s docs for the NF2 chipset and haven’t been able to find any. Well, I’ve solved that problem.

  LAURA KINSALE UNCERTAIN MAGIC PDF

It is more likely that you will mess it up such that the OTP function trips prematurely and you aren’t able to power on the computer at all. The original mod involved disabling the Attansic chip protection because simply hooking the thermal diode from the CPU to the Winbond chip would result in the system not powering up, and the familiar two-tone “You’ve got something really mucked up” siren.

Check out our agtp1 site! BB code is On. You will need to carefully lift this pin from the solder pad. These pins are VERY delicate! Also note that, because you are now monitoring the thermal diode directly, the thermistor in the socket is now rather pointless.

I find that the sttp1 of a single-edge razor blade works rather well for helping lift this pin while I apply heat with the soldering iron. The possibilities are endless!