Kenty PDF

manual, RUN/STOP, and alarms) and the PV or SV. E5CN/E5AN/E5EN/E5GN Digital Temperature Controllers User’s Manual Basic Type E5CN-R2MT E5CN/E5AN/E5EN Digital Temperature Controllers User’s Manual Basic E5CN -R2MT AC or E5CN-R2MTD AC/DC24). E5CN/E5CN-U Temperature Controller User’s Manual (Cat. No. H). E5CN Temperature Controller Communications User’s Manual (Cat. E5CN-R2MT-

Author: Meztigor Kira
Country: Lesotho
Language: English (Spanish)
Genre: Art
Published (Last): 12 November 2017
Pages: 197
PDF File Size: 12.36 Mb
ePub File Size: 14.26 Mb
ISBN: 909-8-85801-907-2
Downloads: 2898
Price: Free* [*Free Regsitration Required]
Uploader: Dirn

Design the system e.

EUROTHERM ERO LFS Controller PID Heater Break Alarm Rs485 W/ Manual Hardware

Output when an input error output is enabled in the Advance Function Setting Level. Use the Temperature Controller within a power supply voltage and load that meet all specifications and ratings. Consult with your OMRON representative at any time to confirm actual specifications of purchased product.

Multi-input Capability with One Controller Connect to either a thermocouple or platinum resistance thermometer with the e5cb-r2mt-500 model.

Recommended panel thickness is 1 to 5 mm. If the control output terminals are connected to ground, errors will occur in the measured temperature values as a result of leakage current.

It will require 2 seconds for the outputs from the Temperature Controller to stabilize after turning ON the power supply. Doing so may occasionally result in minor electric shock, fire, or damage to equipment. Do not apply unnecessary force.

  IEC 62128-1 PDF

When extending or connecting the mabual wire of the platinum resistance thermometer, be sure to use wires that have low resistance and keep the resistance of the three lead wires the same. An SELV circuit is one separated from the power supply with double insulation or reinforced insulation, that does not exceed 30 V r. Alternately tighten the two screws a little at time to keep them balanced. Minimum detection ON time: The input type setting numbers have changed to allow for multiinput specifications.

Analog input This data sheet is provided as a guideline for selecting products.

Refer to Precautions on page Locations subject vibration or strong shock 2. Refer to the ntlp: Component service life is affected by the ambient temperature: Set the alarm types for alarms 1 to 3 independently in the initial setting level. Press the Level Key for at least 3 s.

If an input error output is enabled, the al-1 operation indication on the manua, panel will not light and s. Connect to either a thermocouple or platinum resistance thermometer with the same model.

If an input error output is enabled, the a operation indication on the front panel will not light and s. Use this Adapter when the panel has been previously prepared for the E5B.

  AHMET SAMSUNLU PDF

OMRON E5CN Datasheet: Ordering Information

Terminal applications depend on the model of the Option Unit. E5CN-C Models with Current Outputs Easy, Dependable, and Even Faster Easy Setting with segment Displays The new E5CN features segment displays to make text easier to read, eliminating e5cn-r2mt-50 need to decode displays when trying to set parameters, as was necessary with previous temperature controllers.

Removing the Controller from the Case When carrying out maintenance on mmanual Controller, the Controller can be removed from the case with the terminal leads still attached. The baud rate, data bit length, stop bit length, and vertical parity can be individually set using the Communications Setting Level.

E5CN-R2T manual datasheet & applicatoin notes – Datasheet Archive

Easy, Dependable, Complete Functionality, and segment Displays. Failure to do e5cn-r2mt-5500 may result in unexpected operation occasionally resulting in damage to equipment or personal injury.

When using a grounding thermocouple, do not connect any of the control output terminals to ground. Precautions for Safe Use 1. The terminal arrangement, terminal sizes, and depth for panel mounting have not been changed.